Turn on suggestions
![]() Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
|
08-01-2012 04:39 AM
hi can anybody explain the error below
link is 2 G using Multiplexer device , i have very slow transfer rate max 17MB/s and when i run spinfab i got error
DCX-Lower-sw01:admin> spinfab -ports 2/19
Running spinfab ..............
ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,
Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 72814901,
Err# 13A012E 0242
spinfab: Completed 11 megs, status: FAILED.
port 83 test status: 0x00000002 -- FAILED.
FAILED.
08-01-2012 02:16 PM
any help
08-01-2012 02:21 PM
--->>>...link is 2 G using Multiplexer device
is the link as xWDM ?
have you tried to Fix the Port Speed at 2G instead AN ?
08-01-2012 02:30 PM
Hi here full details
portspeed on both side is N2 ( auto)
we have huawei dwdm fc200 2.125G fiber link connect two DataCenter , when we issue spinfab we got the below error , kindly advice
DCX-Lower-sw01:admin> spinfab -ports 2/19
Running spinfab ..............
ERROR: DIAG PORTSTOPPED spinfab:spinfab, 0 nMegs,
Pt2/19(66) Ch1/26 No Longer Transmitting, FTX Counter Stuck at 89583125,
Err# 13A012E 0242
spinfab: Completed 11 megs, status: FAILED.
port 83 test status: 0x00000002 -- FAILED.
FAILED.
DCX-Lower-sw01:admin>
kindly note link transfer rate is slow we got as max 16MB/s.
siwtches DS-4900B FOS v5.1.0a
DCX-4S FOS v6.4.2a
is there any parameter to change on brocade
----------------
fcping 10:00:00:05:1e:04:be:18
Destination: 10:00:00:05:1e:04:be:18
Pinging 10:00:00:05:1e:04:be:18 with 12 bytes of data:
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1385 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1284 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1227 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1264 usec
received reply from 10:00:00:05:1e:04:be:18: 12 bytes time:1676 usec
5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout
Round-trip min/avg/max = 1227/1367/1676 usec
-------------------
DCX-Lower-sw01:admin> islshow
1: 17-> 23 10:00:00:05:33:5c:98:3a 43 HP_Enc1_sw1 sp: 8.000G bw: 8.000G
2: 72-> 0 10:00:00:05:33:5c:98:3a 43 HP_Enc1_sw1 sp: 8.000G bw: 8.000G
3: 83-> 44 10:00:00:05:1e:04:be:18 1 Fabric-A sp: 2.000G bw: 2.000G
--------------
portshow 2/19
portIndex: 83
portName:
portHealth: HEALTHY
Authentication: None
portDisableReason: None
portCFlags: 0x1
portFlags: 0x10004907 PRESENT ACTIVE E_PORT G_PORT LOGICAL_ONLINE LOGIN LED
LocalSwcFlags: 0x0
portType: 17.0
portState: 1 Online
Protocol: FC
portPhys: 6 In_Sync portScn: 16 E_Port
port generation number: 12098
state transition count: 22
portId: 1b5300
portIfId: 43220802
portWwn: 20:53:00:05:33:25:49:00
portWwn of device(s) connected:
Distance: normal
portSpeed: N2Gbps
LE domain: 0
FC Fastwrite: OFF
Interrupts: 0 Link_failure: 63 Frjt: 0
Unknown: 0 Loss_of_sync: 22 Fbsy: 0
Lli: 203 Loss_of_sig: 42
Proc_rqrd: 415367 Protocol_err: 0
Timed_out: 0 Invalid_word: 565795
Rx_flushed: 0 Invalid_crc: 0
Tx_unavail: 0 Delim_err: 0
Free_buffer: 0 Address_err: 2
Overrun: 0 Lr_in: 19
Suspended: 0 Lr_out: 13
Parity_err: 0 Ols_in: 3
Suspended: | 0 | Lr_out: | 13 |
Parity_err: | 0 | Ols_in: | 3 |
2_parity_err: | 0 | Ols_out: | 36 |
CMI_bus_err: | 0 |
Port part of other ADs: No
08-01-2012 02:30 PM
so what do you think
08-01-2012 02:39 PM
--->>>so what do you think
->siwtches DS-4900B FOS v5.1.0a
->DCX-4S FOS v6.4.2a
->is there any parameter to change on brocade
FOS 6.4.x is not supported with FOS v5.1.x and required a minimum Release of FOS 5.3.2 or higher.
I would first upgarde the FOS.
before you start Upgrade, check compatibility Matrix about Supported Array, HBA and other Connectivity.
08-01-2012 02:45 PM
many thanks
can you tell which document say FOS 6.4.x is not supported with FOS v5.1.x
08-01-2012 02:49 PM