CA OPS/MVS

Expand all | Collapse all

OPSMVS GDI QUESTION

  • 1.  OPSMVS GDI QUESTION

    Posted 02-18-2019 12:39 PM

    I would like to email out an Health Checker exception to certain teams, So once OPSMVS gets the exception I run a Health Checker utility to print the exception out to the log using GDI (No HC exception history because we can't have logstream running on these system).  So i put the output in the OPSLOG,using GDI with message ID of HCALERT0.  How can i email this information or capture this information with AOF, it's not a MLWTO message so can't capture it that way.  Any suggestions?  

     

    Example:

     

    HCALERT0 CHECK(IBMGDPS,GDPS_CHECK_STATE)
    HCALERT0 SYSPLEX: PLEX1 SYSTEM: KPP1
    HCALERT0 START TIME: 02/18/2019 12:10:59.507087
    HCALERT0 CHECK DATE: 20170131 CHECK SEVERITY: MEDIUM
    HCALERT0 GDPS CHECK VERSION: 3.14.2 LEVEL: PI95001 COMPILE: 2018.102 08:17:43
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 ******* Monitor1 check for GDPPNV *******
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 Last Monitor1 run : 2019-02-18 at 12:06:44
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 Next Monitor1 run : 2019-02-18 at 12:11:44
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 Monitor1 interval : 300 seconds
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 Next monitor1 in: 46 seconds
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0 VPC8SHRV VPC8SHRV verbose mode: 00
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 ******* GDPS task check for GDPPNV ******
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 No GDPS task checked inactive
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 ******* GDPS operator check for GDPPNV **
    HCALERT0
    HCALERT0 GEOH007I VPC8C004 No GDPS operator checked queue excessive condition



  • 2.  Re: OPSMVS GDI QUESTION

    Posted 02-19-2019 09:44 AM

    Hi Randy,

     

    You mentioned once OPSMVS gets the exception you print the exception out to the log. Is the contents of the exception not already in the OPSLOG...  You can use CA OPS to send emails in rules, or rexx programs...

    If not all the data is included in the original HC exception, the messages you send to the OPSLOG have the MessageID of HCALERT0.. You could write a MSG rule on this MessageID and create an email... 

     

    If any help needed, please raise case and we could examine it a little closer...

    Or if some other CA OPS user has any advice... Please let Randy know..

     

    Best regards,

    Hennie Hermans

    Broadcom