Hi All,
I have issues about LACP configuration on ProxySG. The Issues are experienced on the Citrix LB connected to the Proxy interfaces that will participate in a LACP deployment.
The issues is arises when the Citrix reports that the aggregate interface is up, but the ProxySG reports a state of synchronizing alway not change to Up.
The ProxySG is connected to a Citrix LB as per below details.
SG Interface 3:0 -- Citrix LB port 10/1
SG Interface 3:1 -- Citrix LB port 10/2
## Citrix LB Interfaces Setup ##
> show interface 10/1
1) Interface 10/1 (10G Ethernet, LR fiber SFP+, 10/1 Gbit) #14
flags=0x400c020 <ENABLED, UP, BOUND to LA/1, UP, autoneg, 802.1q>
MTU=1500, MAC=00:e0:ed:6c:03:5c, uptime 0h33m57s
Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,
throughput 0
Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000
LLDP Mode: NONE, LR Priority: 1024
RX: Pkts(1512244498) Bytes(98180886852) Errs(0) Drops(56290) Stalls(0)
TX: Pkts(578723770) Bytes(40490920800) Errs(0) Drops(58368) Stalls(0)
NIC: InDisc(938548) OutDisc(0) Fctls(0) Stalls(0) Hangs(0) Muted(164)
Bandwidth thresholds are not set.
> show interface 10/2
1) Interface 10/2 (10G Ethernet, LR fiber SFP+, 10/1 Gbit) #15
flags=0x400c020 <ENABLED, UP, BOUND to LA/1, UP, autoneg, 802.1q>
MTU=1500, MAC=00:e0:ed:6c:03:5d, uptime 1h39m53s
Requested: media AUTO, speed AUTO, duplex AUTO, fctl OFF,
throughput 0
Actual: media FIBER, speed 10000, duplex FULL, fctl OFF, throughput 10000
LLDP Mode: NONE, LR Priority: 1024
RX: Pkts(1374577795) Bytes(83954335215) Errs(0) Drops(156229) Stalls(0)
TX: Pkts(576371711) Bytes(42029377354) Errs(0) Drops(30) Stalls(0)
NIC: InDisc(12446321) OutDisc(0) Fctls(0) Stalls(0) Hangs(0) Muted(0)
Bandwidth thresholds are not set.
## LACP Setup ##
> show interface LA/1
1) Interface LA/1 (802.3ad Link Aggregate) #19
flags=0x100c020 <ENABLED, UP, AGGREGATE, UP, HAMON, HEARTBEAT, 802.1q>
MTU=1500, native vlan=80, MAC=02:e0:ed:63:05:e4, uptime 1h40m14s
Requested: media NONE, speed AUTO, duplex NONE, fctl OFF,
throughput 0
Actual: throughput 20000
LLDP Mode: NONE, LR Priority: 1024
RX: Pkts(2886493683) Bytes(182113350354) Errs(0) Drops(212492) Stalls(0)
TX: Pkts(1154110112) Bytes(82454461579) Errs(0) Drops(58398) Stalls(0)
NIC: InDisc(13384869) OutDisc(0) Fctls(0) Stalls(0) Hangs(0) Muted(186)
Bandwidth thresholds are not set.
LA mode: MANUAL
10/1: FIBER-10000-FULL-OFF UP 0h34m18s
10/2: FIBER-10000-FULL-OFF UP 1h40m14s
## VLAN Setup ##
> show vlan 80
1) VLAN ID: 80 VLAN Alias Name:
Dynamic Routing: Enabled
Channels : LA/1 LA/2 LA/3 LA/6(T)
IPs :
xxx.78.yyy.157 Mask: 255.255.255.240
>
## ProxySG Interfaces Setup ##
BC-CM-Caching-01#show interface aggr:0
Aggregate interface aggr:0
Status: enabled
MTU size: 1500
LACP state: 2 Synchronizing
Reject inbound: disabled
Allow intercept: enabled
VLAN trunk: enabled
Native VLAN: 1
Spanning tree: disabled
IPv6 auto-linklocal: enabled
Member of the bridge: none
Routing domain: default
Member interfaces:
Ethernet interface 3:0
Status: enabled
LACP State: Synchronizing
Internet address: xxx.78.yyy.164 netmask 255.255.255.240
Internet address: xxxxxxxxxxxxx:fe32:417a prefixlen 64
Link status: autosensed to full duplex, 10 gigabit/sec network
Ethernet interface 3:1
Status: enabled
LACP State: Synchronizing
Link status: autosensed to full duplex, 10 gigabit/sec network
BC-CM-Caching-01#show interface 3:0
Ethernet interface 3:0
Status: enabled
Internet address: xxx.78.yyy.164 netmask 255.255.255.240
Internet address: xxxxxxxxxxxxx:fe32:417a prefixlen 64
MTU size: 1500
Link status: autosensed to full duplex, 10 gigabit/sec network
Reject inbound: disabled
Allow intercept: enabled
VLAN trunk: enabled
Native VLAN: 1
Spanning tree: disabled
IPv6 auto-linklocal: enabled
Routing domain: default
Member of aggregate interface: aggr:0
BC-CM-Caching-01#show interface 3:1
Ethernet interface 3:1
Status: enabled
MTU size: 1500
Link status: autosensed to full duplex, 10 gigabit/sec network
Reject inbound: disabled
Allow intercept: enabled
VLAN trunk: enabled
Native VLAN: 1
Spanning tree: disabled
IPv6 auto-linklocal: enabled
Routing domain: default
Member of aggregate interface: aggr:0
I have tried to do as KB below but still not work
https://support.symantec.com/en_US/article.TECH246138.embed.html
Please advise me.
Best Regards,
T.Jitrak