For more details, please see ourCookie Policy.


Fibre Channel (SAN)

Reply
New Contributor
Posts: 2
Registered: ‎02-12-2015

Switch SAN reboot [HAM-1004]

The system is coming up, please wait...


U-Boot 1.1.3 (Jun 26 2017 - 08:33:41)

CPU:   8548, Version: 3.1, (0x80310031)
Core:  E500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU:1199 MHz, CCB: 399 MHz,
       DDR: 199 MHz, LBC:  49 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: Odin
CPU Board Revision 255.198 (0xffc6)
    PCI2: disabled
I2C:   ready
DRAM:  initdram: Initializing DDRSDRAM
initdram: Normal boot in progress
dimm_spd_sdram 2001: memsize = 800
initdram: Call ddr_enable_ecc dram size -2147483648
    DDR: 2048 MB
POST RAM test disabled.
Adjusted memory 0x7d000000 2097152000
Now running in RAM - U-Boot at: 74f7d000
trap_init : 0x0
system inventory subsystem initialized
FLASH:  4 MB
L2 cache 512KB: enabled
CPLD: odin_cpld_reset
Init complete
ATA interface setup upm 256: ffcff00, ffcfc04, ffffc00, fffffc01
PCI: gd->brcd_flags = 0, PCI init
Skip our host bridge
        00  14  1033  0035  0c03  35
        00  14  1033  00e0  0c03  35
        83  00  1657  001d  0280  1a
        82  01  10b5  8608  0604  1a
        84  00  1657  001d  0280  1a
        82  04  10b5  8608  0604  32
        85  00  1657  001d  0280  1a
        82  05  10b5  8608  0604  1a
        86  00  1657  001d  0280  1a
        82  06  10b5  8608  0604  1a
        87  00  1657  001d  0280  1a
        82  07  10b5  8608  0604  1a
        88  00  1657  001d  0280  1a
        82  08  10b5  8608  0604  1a
        82  09  10b5  8608  0604  1a
        81  00  10b5  8608  0604  1a
In:    serial
Out:   serial
Err:   serial
Net:
ENET0: PHY is Broadcom BCM54610 10/100/1000 BaseT PHY (143bd63)

board_init_r: Adjusted ram 2097152000 0x7d000000 2048000k
Checking system RAM - press any key to stop test

Checking memory address: 00100000

System RAM test using Default POST RAM Test succeeded.

set_bootstatus: BS_LOAD_OS, platform_idx = 18
Hit ESC to stop autoboot:  0
Map file at LBA sector 0x8bdd7
do_bootm 171: load_addr 0x02000000 addr 0x00400000
do_bootm 174: ## Booting image at 00400000 load_addr 0x02000000 ...
   Image Name:   Linux-2.6.14.2
   Image Type:   PowerPC Linux Multi-File Image (gzip compressed)
   Data Size:    2675431 Bytes =  2.6 MB
   Load Address: 00000000
   Entry Point:  00000000
   Contents:
   Image 0:  1596756 Bytes =  1.5 MB
   Image 1:  1078663 Bytes =  1 MB
   Uncompressing Multi-File Image ... do_bootm_linux 565: ## Current stack ends at 0x74F5BB38 => set upper limit to 0x00800000
## initrd at 0x00585DA0 ... 0x0068D326 (len=1078663=0x107587)
   Loading Ramdisk to 1fef8000, end 1ffff587 ... OK
 initrd_start = 1fef8000, initrd_end = 1ffff587
## Transferring control to Linux (at address 00000000) ...
tlbcam_index=11
mpc85xx_setup: Doing Pcie bridge setup
Scanning PcieBus...
PCI: 0000:00:00.0: class b20 doesn't match header type 01. Ignoring class.

Installing Linux 2.6 Kernel
Attempting to find a root file system on hda1...
INIT: version 2.78 booting
Bypassing firmware validation.
INIT: Entering runlevel: 3
Starting Fabric OS Services...
FIPS off, RRD...
Found 1(threshold 5) abnormal reboots within 3000 seconds window(threshold)

pdcheck: info: found new pd: mtd_ts=1536924772 PANIC Fri Sep 14 11:32:52 2018, cf_ts=1536924565
pdcp:readHeader:283 invalid save timestamp ref=1536924772 hdr=1536924565
pdcheck: pdcp failed to copy the files (err = 2)
FPGA address is 0xbfc8a000
Completed registering ASIC interrupts
pcie_error_init: msr 0x00029200 mcsr 0x00000000  hid0 0x80004080 hid1 0x46003000
Interrupts turned on from Platform
sys_chip_init: class 0 max 24 Done
ethsw_ha_enabled = 1
uptime: 4293889288; sup_qid: 0
2018/09/14-11:52:17, [HAM-1004], 241, CHASSIS, INFO, IBM_2498_F96, Processor rebooted - Software Fault:ASSERT.

2018/09/14-11:52:21, [TRCE-1001], 242, CHASSIS, WARNING, IBM_2498_F96, Trace dump available ! (reason: PANIC).
2018/09/14-11:52:21, [TRCE-1004], 243, CHASSIS, WARNING, IBM_2498_F96, Trace dump  was not transferred because trace auto-FTP disabled.
SNMP Research EMANATE/Lite Agent Version 16.2.0.9
Copyright 1989-2006 SNMP Research, Inc.
2018/09/14-11:52:25, [FV-1001], 244, CHASSIS, INFO, SW11P, Flow Vision daemon initialized.
2018/09/14-11:52:40, [FCR-1069], 245, FID 126, INFO, SW11P_BASE, The FC Routing service is enabled.
2018/09/14-11:52:40, [FCR-1068], 246, FID 126, INFO, SW11P_BASE, The FC Routing service is disabled.
2018/09/14-11:52:41, [FV-1002], 247, FID 127, INFO, SW11P_PRIVE, Flow Vision Config Replay Completed Successfully.
2018/09/14-11:52:41, [FV-1002], 248, FID 126, INFO, SW11P_BASE, Flow Vision Config Replay Completed Successfully.
ki_state_set: redundant ACTIVATE for instance 1
2018/09/14-11:52:42, [MAPS-1201], 249, FID 127, INFO, SW11P_PRIVE,  MAPS has started monitoring with dflt_conservative_policy policy.
2018/09/14-11:52:42, [FV-1002], 250, FID 128, INFO, SW11P, Flow Vision Config Replay Completed Successfully.
2018/09/14-11:52:42, [ZONE-1022], 251, FID 128, INFO, SW11P, The effective configuration has changed to PROD_NORMALE_FABRIC_1.
2018/09/14-11:52:43, [MAPS-1201], 252, FID 126, INFO, SW11P_BASE,  MAPS has started monitoring with dflt_conservative_policy policy.
2018/09/14-11:52:45, [TS-1001], 253, FID 128, WARNING, SW11P, NTP Query failed: 256.
2018/09/14-11:52:45, [MAPS-1201], 254, FID 128, INFO, SW11P,  MAPS has started monitoring with dflt_base_policy policy.
Sep 14 11:52:45  All service instances on Active
Failure at function c3_phy_cfg_init line:1380 val:0x43029030 -1 0x0 -1 0
c3_phy_cfg_init failed for chip:43011880 port_idx:32


MSR: 00029200 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 0/0
TASK = b3c9f220[1976] 'emd0' Last syscall: 54
ASSERT - Failed expression: bp->bp_asic != NULL,
         file = /vobs/projects/springboard/build/swbd62/fabos/src/sys/dev/blade/pulsar/pulsar_port.c, line = 292, kernel mode
Call backtrace:
Trace: c1f140f0 <pulsar_bport_create+0x248/0x7f4 [pulsar_blade_module]>
Trace: c1f34600 <blade_hierarchy_instantiate+0xc18/0x18b0 [pulsar_blade_module]>
Trace: c1f2f0c8 <odin_inst+0x1ec/0x5f8 [pulsar_blade_module]>
Trace: c08bf510 <fabsys_blade_instantiate+0x50/0x6c [fabsys_module]>
Trace: c1cb4ee0 <chassis_blade_init+0xc4/0x3ec [chassis_module]>
Trace: c08bea5c <fabsys_chassis_blade_init+0x58/0x74 [fabsys_module]>
Trace: c08c7ea8 <_rdy+0x5e4/0x12a4 [fabsys_module]>
Trace: c08c59fc <fsm_controller+0x238/0x2fc [fabsys_module]>
Trace: c08c5e64 <sys_fsm_dft_ctrl+0x2b4/0x754 [fabsys_module]>
Trace: c08c3b58 <unkn_slot_class_hndlr+0x94/0x104 [fabsys_module]>
Trace: c08c3f08 <slot_class_hndlr+0x128/0x2b0 [fabsys_module]>
Trace: c08c38d0 <sysScnProcState+0x84/0x160 [fabsys_module]>
Trace: c08b94a4 <sysCtrlProcCmd+0x5a14/0x6d24 [fabsys_module]>
Trace: c08af5c0 <fabsys_ioctl+0x50/0xc4 [fabsys_module]>
Trace: 40072e44 <do_ioctl+0x88/0x9c>
Trace: 40072f10 <vfs_ioctl+0xb8/0x410>
Trace: 400732a8 <sys_ioctl+0x40/0x74>
Trace: 40002430 <ret_from_syscall+0x0/0x48>
Trace: 0dd49874 <0xdd49874>
Trace: 0e51f40c <0xe51f40c>

set_reboot_reason reason=Software Fault:ASSERT
Kernel panic - not syncing: fabos assertion failed cpu 0:
ASSERT - Failed expression: bp->bp_asic != NULL,
         file = /vobs/projects/springboard/build/swbd62/fabos/src/sys/dev/blade/pulsar/pulsar_port.c, line = 292


 PD Start
PowerPC Book-E Watchdog Shutdown soft timer
MTRACER
mtracer_panicdump
mtracer_panicdump write=0x40b5
reboot_reason
PD_MISC
CONSOLE_LOG
KERNEL_STACK_DUMP
PDTRACE
Start ATA tracedump

Join the Broadcom Support Community

Get quick and easy access to valuable resources across the Broadcom Community Network.