Turn on suggestions
![]() Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
|
10-29-2015 10:57 AM
Good afternoon Antonio
I have a Brocade Fabric OS: V6.1.1, which only allows access via serial port.
For example
ping 192.168.30.70 does not respond to ping
The following tests have already been made, but without successfull
Exchange Ip /
Gate speed change
cable cross over
reboot Switch
Power on / off
There is an alternative to the problem?
Kernel: 2.6.14.2
Fabric OS: v6.1.1
Made on: Mon Aug 18 17:16:17 2008
Flash: Fri Jun 5 06:31:51 2009
BootProm: 1.0.6
10-29-2015 11:24 AM
Alessandro,
was the switch in the past reachable trough the managemend interface ?
try/check with the command "ipfilter" if any Rules is set, is most probable a Rule was set to the port I.E. instead IPv4 to IPv6
for details and operands refer teh Command Reference Manual
11-11-2015 02:33 AM
Hi Antonio,
There is no policy to ipv4.
Which directory is the network configuration files in Fabos with User root.
bvsansw03:root> ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:05:1E:A1:60:DF
inet addr:192.168.30.70 Bcast:192.168.30.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4202 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
fc0 Link encap:UNSPEC HWaddr 00-05-1E-A1-60-DF-10-00-00-00-00-00-00-00-00-00
BROADCAST MTU:2024 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.255.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4295083 errors:0 dropped:0 overruns:0 frame:0
TX packets:4295083 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
port0 Link encap:Ethernet HWaddr 00:05:1E:A1:60:DF
BROADCAST NOARP MULTICAST MTU:2112 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
sit0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-10-00-00-00-00-00-00-00-00-00
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
Why Eth0 has same Mac that Port0?
11-11-2015 10:17 AM
can you please post from command line the output from "ipaddrshow"
11-24-2015 04:49 PM
Hi Antonio,
Was executed this command with root user:
ifconfig eth0 down
After that the IP was changed e Ethernet Port Status ok,
Comand Ping ok and web tools ok
PS.o Comand ifconfig eth0 up, doesnt Work
Tks your Support