Ethernet Switches Community

Expand all | Collapse all

from where can I get the reference schematics of BCM53286

  • 1.  from where can I get the reference schematics of BCM53286

    Posted 11-18-2018 10:25 PM

     I am using BCM53286 in my design as an Fe switch. Can I get a reference schematic or related documents for the same?


    #EthernetSwitchesCommunity


  • 2.  Re: from where can I get the reference schematics of BCM53286

    Posted 11-19-2018 10:08 PM
      |   view attached

    Hi,

    Firstly please find the attached BCM953286R reference board schmeatic file.

     

    Thanks,

    Ryan


    #EthernetSwitchesCommunity

    Attachment(s)

    pdf
    BCM953286R_0924.pdf   713K 1 version


  • 3.  Re: from where can I get the reference schematics of BCM53286

    Posted 12-03-2018 05:15 AM

    Thanks Ryan,

     

    will come back to you with our doubts.


    #EthernetSwitchesCommunity


  • 4.  Re: from where can I get the reference schematics of BCM53286

    Posted 01-03-2019 10:24 PM

    Is 3.3v compatible to 2.5V? Do we need to translate 3.3 to 2.5v for MDIO and MDC?


    #EthernetSwitchesCommunity


  • 5.  Re: from where can I get the reference schematics of BCM53286

    Posted 01-03-2019 10:27 PM
      |   view attached

    How can we use 3.3V on termination if there is no 3.3V used in the switch?


    #EthernetSwitchesCommunity


  • 6.  Re: from where can I get the reference schematics of BCM53286

    Posted 01-14-2019 07:23 PM

    Hi,

    Please find the below comment per your two questions.

    1. The MDC, MDIO pins are 3.3V tolerant.

    2. I believe you are refer to our application note "CAP-AN102-R" for the backplane design. Please follow the [Backplane Connection/Termination] Figure you attached and follow the [Table1: Termination Bias Requirements] Device BCM53262/M/S.

     

    Thanks,

    Ryan


    #EthernetSwitchesCommunity


  • 7.  Re: from where can I get the reference schematics of BCM53286

    Posted 02-25-2019 06:08 AM

     Hi Ryan,

     

    Thanks for the above reply.  A few more queries:

    1. According to the datasheet, the pins XTALI and XTALO are not 3.3 V tolerant. Are other pins in this device 3.3 V tolerant? 
    2. Can SPI and reset coming from CFPGA(3.33V) compatible to the BCM device pins? If not, how should they be connected?


    #EthernetSwitchesCommunity


  • 8.  Re: from where can I get the reference schematics of BCM53286

    Posted 03-04-2019 07:32 PM

    Hi,

    Please find the comment below per your questions:

    1. Right, the pin XTALI and XTALO are 2.5V level and not 3.3V tolerant.

        The 3.3V tolerant pins are including the configuration pins, programming interface pins, MDC/MDIO pins, LED pins and Reset pin.

    2. It's fine the SPI pins are coming from your CFPGA device, suggest please follow the SPI driver in our SDK SW to implement.

        For reset pin, highly recommend to use the external reset device to provide the reset siganl to BCM53286. And please make sure to

        refer to our design guide application note 5328X-AN103-R "Core and I/O Power Sequencing Requirement" section to tollow our

        power on sequencing requirement.

     

    Thanks,

    Ryan


    #EthernetSwitchesCommunity


  • 9.  Re: from where can I get the reference schematics of BCM53286

    Posted 03-12-2019 11:58 PM

    Hi,  

     

    Thanks for the reply. Cna you please share the documents you have mentioned in the reply above.

     

    Thanks & Regards,

    Megha Agarwal


    #EthernetSwitchesCommunity


  • 10.  Re: from where can I get the reference schematics of BCM53286

    Posted 03-14-2019 07:22 PM

    Hi,

    For the doc 5328X-AN103-R, please go to the BCM53286 folder in this community site and download it.

     

    Thanks,

    Ryan


    #EthernetSwitchesCommunity