Brocade Fibre Channel Networking Community

Expand all | Collapse all

HP c7000 enclosure moved Blade from one chassis to another

  • 1.  HP c7000 enclosure moved Blade from one chassis to another

    Posted 04-01-2014 09:43 AM

    And now the blade is in persistent disable mode and will not respond to anything.

     

    I have tried

        1. portcfgdefault

        2. portdisable

        3. portenable

     

    It comes up with the following error

    Switch may be disabled, POD license is NOT installed, 7500E upgrade license is NOT installed, slot is off, port is persistently disabled or if this is VE port and associated GE is not in FCIP mode.

     

    WT says port is Persistent Disable and both enable and disable are greyed out.

     

    here is port cfg

    portName: 

    portHealth: No Fabric Watch License

     

    Authentication: None

    portDisableReason: Persistently disabled port

    portCFlags: 0x0

    portFlags: 0x21 PRESENT DISABLED

    portType:  11.0

    POD Port: Port is licensed

    portState: Persistently Disabled

    portPhys:  5No_Sync  

    portScn:   2Offline   

    port generation number:    224

    portId:    070b00

    portIfId:    4302000d

    portWwn:   20:0b:00:05:1e:09:fe:7b

    portWwn of device(s) connected:

     

    Distance:  normal

    portSpeed: Negotiating

     

    LE domain: 0

    FC Fastwrite: OFF

    Interrupts:        0          Link_failure: 0          Frjt:         0          

    Unknown:           0          Loss_of_sync: 0          Fbsy:         0          

    Lli:               0          Loss_of_sig:  0          

    Proc_rqrd:         0          Protocol_err: 0          

    Timed_out:         0          Invalid_word: 0          

    Rx_flushed:        0          Invalid_crc:  0          

    Tx_unavail:        0          Delim_err:    0          

    Free_buffer:       0          Address_err:  0          

    Overrun:           0          Lr_in:        0          

    Suspended:         0          Lr_out:       0          

    Parity_err:        0          Ols_in:       0          

    2_parity_err:      0          Ols_out:      0          

    CMI_bus_err:       0          

     

    Port part of other ADs: No

     

    switch has a current fabric license

     

    I tried to persistentenable in WT and it said Operation is not supported on this port.

     

     


    #BrocadeFibreChannelNetworkingCommunity


  • 2.  Re: HP c7000 enclosure moved Blade from one chassis to another

    Posted 04-01-2014 12:29 PM

    Try portcfgpersistentenable.


    #BrocadeFibreChannelNetworkingCommunity


  • 3.  Re: HP c7000 enclosure moved Blade from one chassis to another

    Posted 04-02-2014 06:25 AM

    No dice 

     

    I get the following

     

    portcfgpersistentenable 11

    portcfgpersistentenable failed.  Operation not supported.


    #BrocadeFibreChannelNetworkingCommunity


  • 4.  Re: HP c7000 enclosure moved Blade from one chassis to another

    Posted 04-02-2014 07:16 AM

    Mezz cards were 8gig and i swapped them to 4 gig.

     

    Still the same issue.

     

     

     

     


    #BrocadeFibreChannelNetworkingCommunity


  • 5.  Re: HP c7000 enclosure moved Blade from one chassis to another

    Posted 07-16-2014 04:45 PM

     

    Did you end up getting a resolution for this portcfgpersistentenable operation failed?

    I'm getting the same issue on my C7000 chassis.


    #BrocadeFibreChannelNetworkingCommunity