Brocade Fibre Channel Networking Community

Expand all | Collapse all

DCX Change Slot - port error

Jump to Best Answer
  • 1.  DCX Change Slot - port error

    Posted 05-21-2014 09:18 AM

    Hi all!

     

    My case is about a Slot replace on a DCX 4S Backbone. After the change, one port is fault. This port is an ISL port. I check the Port health, and FO too, and is OK. Change SFPs, loop FO and port in both sides of the conn.

    In the log, the count grows in the items "link Failure" and "Outbound Offline Sequence".

    Any ideas about what is wrong? 

     

    Thanks !!!

     

    Cesar


    #BrocadeFibreChannelNetworkingCommunity


  • 2.  Re: DCX Change Slot - port error

    Posted 05-27-2014 12:59 AM

    Hi Cesar,

     

    What error are you seen? According to the description provided, there could be an issue with the connectivity to the other end of the ISL.

     

    please post the output of:

    portshow

    portcfgshow

    portstatsshow

    switchshow |grep

     

     

     

    Rgds,

    Felipon


    #BrocadeFibreChannelNetworkingCommunity


  • 3.  Re: DCX Change Slot - port error

    Posted 06-11-2014 08:15 AM
      |   view attached

    Hi Felipon!

    Thanks for the Reply. In the last few days we check the FO, and the results was good. There's no problem whith the Fiber Channel.

    I attach a file with the output of the commands that you show me, in both ports of the ISL. The ports was moved to the switch 127 to preserve the health of the ISL in the Switch1 (ISL).

     

    Regards!
    Cesar

    I hope that you understand my english! 

     


    #BrocadeFibreChannelNetworkingCommunity

    Attachment(s)

    pdf
    BrocadeDCX-ISL_01.pdf   55K 1 version


  • 4.  Re: DCX Change Slot - port error

    Posted 06-17-2014 08:50 AM

    There may be an issue with the link communication or the sfp could be faulted...

    have you tried to portdisable/portenable both ends?

     

    please post the output of: 

     

    switchshow |grep -e 34 -e 247

    sfpshow 3/2

     

     

    rgds


    #BrocadeFibreChannelNetworkingCommunity


  • 5.  Re: DCX Change Slot - port error

    Posted 06-19-2014 01:02 PM

    Hi!

     

    I send the output.

     

    regards!

    Cesar


    #BrocadeFibreChannelNetworkingCommunity


  • 6.  Re: DCX Change Slot - port error

    Posted 06-19-2014 01:12 PM

    Switch1 -F


    Test:FID127:admin> switchshow |grep -e 34 -e 247
    34 3 2 02f740 id N8 Port_Flt FC LD
    Test:FID127:admin> sfpshow 3/2
    Identifier: 3 SFP
    Connector: 7 LC
    Transceiver: 5401101200000000 2,4,8_Gbps SM lw Long_dist
    Encoding: 1 8B10B
    Baud Rate: 85 (units 100 megabaud)
    Length 9u: 25 (units km)
    Length 9u: 250 (units 100 meters)
    Length 50u (OM2): 0 (units 10 meters)
    Length 50u (OM3): 0 (units 10 meters)
    Length 62.5u:0 (units 10 meters)
    Length Cu: 0 (units 1 meter)
    Vendor Name: BROCADE
    Vendor OUI: 00:05:1e
    Vendor PN: 57-0000080-01
    Vendor Rev: A
    Wavelength: 1310 (units nm)
    Options: 001a Loss_of_Sig,Tx_Fault,Tx_Disable
    BR Max: 0
    BR Min: 0
    Serial No: UBA111301002141
    Date Code: 110731
    DD Type: 0x68
    Enh Options: 0xf0
    Status/Ctrl: 0x82
    Alarm flags[0,1] = 0x0, 0x0
    Warn Flags[0,1] = 0x0, 0x0
    Alarm Warn
    low high low high
    Temperature: 36 Centigrade -40 90 -10 85
    Current: 31.670 mAmps 2.000 95.000 2.000 80.000
    Voltage: 3226.4 mVolts 2700.0 3800.0 2970.0 3630.0
    RX Power: -3.1 dBm (484.8uW) 1.0 uW 1260.0 uW 25.0 uW 1129.9 uW
    TX Power: 1.5 dBm (1418.3 uW) 800.0 uW 6000.0 uW 1000.0 uW 5000.0 uW
    State transitions: 3
    Last poll time: 06-19-2014 Localtime Thu 16:54:56
    Test:FID127:admin>

    -------------------------------------------------------------------------------------------

     

    Switch2 –V
    Test:FID127:admin> switchshow |grep -e 34 -e 247
    34 3 2 01f740 id N8 In_Sync FC LD
    Test:FID127:admin> sfpshow 3/2
    Identifier: 3 SFP
    Connector: 7 LC
    Transceiver: 5401101200000000 2,4,8_Gbps SM lw Long_dist
    Encoding: 1 8B10B
    Baud Rate: 85 (units 100 megabaud)
    Length 9u: 25 (units km)
    Length 9u: 250 (units 100 meters)
    Length 50u (OM2): 0 (units 10 meters)
    Length 50u (OM3): 0 (units 10 meters)
    Length 62.5u:0 (units 10 meters)
    Length Cu: 0 (units 1 meter)
    Vendor Name: BROCADE
    Vendor OUI: 00:05:1e
    Vendor PN: 57-0000080-01
    Vendor Rev: A
    Wavelength: 1310 (units nm)
    Options: 001a Loss_of_Sig,Tx_Fault,Tx_Disable
    BR Max: 0
    BR Min: 0
    Serial No: UBA111301000141
    Date Code: 110728
    DD Type: 0x28
    Enh Options: 0xf0
    State transitions: 1
    Last poll time: 06-09-2014 Localtime Mon 12:26:51
    Test:FID127:admin>


    #BrocadeFibreChannelNetworkingCommunity


  • 7.  Re: DCX Change Slot - port error

    Posted 06-19-2014 01:30 PM

    cesar,

     

    you wrote:

     

    --->>>My case is about a Slot replace on a DCX 4S Backbone. 

     

    accordly the latest post and th eoutput the DCX is configure with FID = Fabric ID 127, however Default is 128

     

    Question:

     

    have your configure Logical Switch beetwen the DCX ?

     

    and what you meaning with "Slot replace" ?

     

    have you moved the Port Blade from One Slot to another, in example from slot 1 to slot 3 or have replace the Blade due defective ?


    #BrocadeFibreChannelNetworkingCommunity


  • 8.  Re: DCX Change Slot - port error

    Posted 06-23-2014 06:05 AM

    Hi TechHelp24!

     

    The case is about a Blade replace because the blade due defective. This Blade is inserted in the Slot 3, with two ports ISL on de BASE Switch 1. This ports are 3/2 and 3/47.

    After the replace, the 3/2 port don't reestablish the link.

    This link is configured between 2 Brocade, with the same configuration (slot/port) in two remote sites, witch interconect across a DWDM. I loop the fiber and response positive to both sides, but, when enable the ports, there is not link.

    We move the port from BASE to TEST to isolate the afected ports.

     

    Thanks!

    Cesar

     


    #BrocadeFibreChannelNetworkingCommunity


  • 9.  Re: DCX Change Slot - port error
    Best Answer

    Posted 07-04-2014 05:55 AM

    Hi all!

     

    Well, finally the link is up. I find a solution cleaning the fibre "again".

    I greatly appreciate the support given

     

    Thanks!

     

    Cesar


    #BrocadeFibreChannelNetworkingCommunity