Brocade Fibre Channel Networking Community

6510 failing to boot

  • 1.  6510 failing to boot

    Posted 09-03-2015 09:03 AM

    Hi

     

    I've got a 6510 which looks as though it has corrupt firmware.

    It's constantly rebooting, and when you can log in, no FOS commands will run.

    Is it possible to reflash ?

     

    I can get in to the preboot menu ok.

     

    Cheers,

    Rob

     

    MORD6510_A console login: 2015/09/03-18:50:15, [HAM-1007], 30563, FFDC | CHASSIS, CRITICAL, Brocade6510, Need to reboot the system for recovery, reason: Softt
    2015/09/03-18:50:15, [RAS-1001], 30564, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
    cat: /var/log/fsslo.log: No such file or directory
    2015/09/03-18:50:45, [HAM-1008], 30565, FFDC | CHASSIS, CRITICAL, Brocade6510, Rebooting the system for recovery - auto-reboot is enabled
    2015/09/03-18:50:45, [RAS-1001], 30566, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
    Restarting system.

    The system is coming up, please wait...


    U-Boot 1.1.3 (May 29 2011 - 20:03:39)

    CPU: AMCC PowerPC 440EPx Rev. A at 660 MHz (PLB=132, OPB=66, EBC=33 MHz)
    No Security/Kasumi support
    I2C boot EEPROM enabled
    Bootstrap Option G - Boot ROM Location I2C (Addr 0x54)
    Internal PCI arbiter enabled, PCI async ext clock used
    32 kB I-Cache 32 kB D-Cache
    Board: Stinger
    I2C: ready
    DRAM: Initializing DDRSDRAM
    DQS calibration - Window detected:
    max_passing_cases = 55
    wr_dqs_shift = 90
    dll_dqs_delay_X = 30
    dll_dqs_delay_X window = 3 - 57
    DDR0_09=0x00011d5a
    DDR0_22=0x03267a0b
    DDR0_17=0x1e006300
    DDR0_18=0x1e1e1e1e
    DDR0_19=0x1e1e1e1e
    Zeroing SDRAM... DONE
    DDR: 1024 MB
    POST RAM test disabled.
    Now running in RAM - U-Boot at: 3fb30000
    trap_init : 0x0
    system inventory subsystem initialized
    FLASH: Stinger CFI Flash Driver Initialized
    4 MB

    DEBUG: ASIC Reset Enable Register Offset:0x88 Value:0x03...

    CPLD: Reseting Bridge & ASIC...
    ATA interface setup: io_base=0xf8f00000, port=0x3e0, ctl=0x7ec
    PCI:
    Skip our host bridge
    01 00 1657 001d 0280 1a
    00 07 10b5 8112 0604 18
    In: serial
    Out: serial
    Err: serial
    Net:

    Checking system RAM - press any key to stop test

    Checking memory address: 00100000

    System RAM test using Default POST RAM Test succeeded.

    set_bootstatus: BS_LOAD_OS, platform_idx = 14

    Type run flash_nfs to mount root filesystem over NFS

    Hit ESC to stop autoboot: 0
    Map file at LBA sector 0x113388
    ## Booting image at 00400000 ...
    Image Name: Linux-2.6.14.2
    Image Type: PowerPC Linux Multi-File Image (uncompressed)
    Data Size: 4269595 Bytes = 4.1 MB
    Load Address: 00000000
    Entry Point: 00000000
    Contents:
    Image 0: 3190918 Bytes = 3 MB
    Image 1: 1078663 Bytes = 1 MB
    ## Current stack ends at 0x3FAEEBE8 => set upper limit to 0x00C00000
    ## initrd at 0x0070B0D4 ... 0x0081265A (len=1078663=0x107587)
    Loading Ramdisk to 1fef8000, end 1ffff587 ... OK
    initrd_start = 1fef8000, initrd_end = 1ffff587
    ## Transferring control to Linux (at address 00000000) ...
    Installing Linux 2.6 Kernel
    Attempting to find a root file system on hda2...
    INIT: version 2.78 booting
    Bypassing firmware validation.
    INIT: Entering runlevel: 3
    Starting Fabric OS Services...
    FIPS off, RRD...
    Found 4(threshold 5) abnormal reboots within 3000 seconds window(threshold)
    rscmon_service: started thread!
    rscmon_service: started thread!
    sys_chip_init: class 0 max 24 Done
    ethsw_ha_enabled = 1
    uptime: 4293889222; sup_qid: 0
    .


    Fabric OS (MORD6510_A)


    MORD6510_A console login: 2015/09/03-18:51:26, [HAM-1004], 30567, CHASSIS, INFO, Brocade6510, Processor rebooted - Software Bootup Failure:Bringup timed out

    SNMP Research EMANATE/Lite Agent Version 16.2.0.9
    Copyright 1989-2006 SNMP Research, Inc.


    If your terminal supports lower case letters, please
    use them. Login again, using lower case if possible.


    MORD6510_A console login: 2015/09/03-18:53:44, [HAM-1007], 30568, FFDC | CHASSIS, CRITICAL, Brocade6510, Need to reboot the system for recovery, reason: Softt
    2015/09/03-18:53:44, [RAS-1001], 30569, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.
    cat: /var/log/fsslo.log: No such file or directory
    admin
    Password:
    WARNING! This system is blah blah blah blah blah

    -----------------------------------------------------------------

    Please change passwords for switch default accounts now.
    Use Control-C to exit or press 'Enter' key to proceed.
    Warning: Access to the Root and Factory accounts may be required for
    proper support of the switch. Please ensure the Root and Factory
    passwords are documented in a secure location. Recovery of a lost Root
    or Factory password will result in fabric downtime.

    for user - root
    Changing password for root
    Enter new password:
    Password was not changed. Will prompt again at next login
    until password is changed.
    MORD6510_A:FID128:admin>
    MORD6510_A:FID128:admin> switchshow
    rbash: switchshow: command not found
    MORD6510_A:FID128:admin> 2015/09/03-18:54:14, [HAM-1008], 30570, FFDC | CHASSIS, CRITICAL, Brocade6510, Rebooting the system for recovery - auto-reboot is end
    2015/09/03-18:54:14, [RAS-1001], 30571, CHASSIS, INFO, Brocade6510, First failure data capture (FFDC) event occurred.

    MORD6510_A:FID128:admin> errsRestarting system.

     

     

    -----------------------------------------------------------------
    **************************************************************
    * *
    * Fabric OS has detected frequent switch reboot condition. *
    * Following actions can be taken to recover the switch: *
    * - remove or replace any problem blades (if applicable to *
    * platform). *
    * - use supportsave to collect supportsave data. *
    * *
    **************************************************************
    sysmodAttach open failed: No such device or address
    fabsys device open: No such device or address
    Raslog Module Initialisation failed rc=-1
    fabsys device open: No such device or address

     

     


    #BrocadeFibreChannelNetworkingCommunity