Brocade Fibre Channel Networking Community

Expand all | Collapse all

Brocade 5100 portbuffershow values "E" port

  • 1.  Brocade 5100 portbuffershow values "E" port

    Posted 10-29-2014 03:24 PM

    I set the portlongdistance to LE oand VC_Trans_Link_Init = 1 on an ISL to a 4100 and the Max/Resv Buffers is 46.

    I did the same on another ISL on another 5100 and it only allocated Max/Resv Buffers of 26.

    5100's on same FOS version 7.2.1a

     

    I set the port speeds to 4g and disabled qos on all "E" ports.

     

    Anyone?   

     

    Thanks for any assistance.

     

     

     

     


    #5100
    #BrocadeFibreChannelNetworkingCommunity
    #isl


  • 2.  Re: Brocade 5100 portbuffershow values "E" port

    Posted 10-30-2014 01:38 AM

    Hi,

     

    that result in the Max/resv Buffers is caused because on that end the speed was set to AUTO and forced to 4G on the other end of the ISL.

     

    '46' is the number of reserved BB credits for a speed of 8G in LE mode and since you didn't force the speed, the switch reserves the maximum, just in case it may need it.

     

    I am just speculating so, please, repeat your test but forcing the speed to 4G on both ends of the ISL and let us know if the result fits.

     

    Rgds,

    Felipon

     

     

     


    #BrocadeFibreChannelNetworkingCommunity
    #longdistance
    #LE
    #ils


  • 3.  Re: Brocade 5100 portbuffershow values "E" port

    Posted 10-30-2014 01:55 AM

    You were correct sir - putting port back to auto increased the buffers to 46 on port 33/37.

     

    Another question - the column "Average Buffee Tx" What are values inside and outside parentheses exactly?

    In example below from portbuffershow: Column 5?

    Do I need to increase further beyond the 46, because of the 120 average? This port 38 is connected to a 4100 and has latency errors.

     

     

     33       E      LE        46       - (  68)      - (  64)          26      26        10km
      34       E       -         8       - (  - )      - (  - )          26      26         2km
      35       E       -         8       - (  - )      - (  - )          26      26         2km
      36               -         8       - (  - )      - (  - )           0       -          -
      37       E      LE        46       - (  72)      - (  48)          26      26        10km
      38       E       -         8       - ( 120)      - ( 460)          26      26         2km
      39       E       -         8       - (  80)      - (  60)          26      26         2km      1544


    #BrocadeFibreChannelNetworkingCommunity


  • 4.  Re: Brocade 5100 portbuffershow values "E" port

    Posted 10-30-2014 09:48 AM

    Hi,

     

    The values inside the parenthesis are supposed to be the average Frame size on that link. Whilst the values outside the parenthesis are supposed to be the average buffer usage on that link. A good example is shown in the following link

     

    In your particular case, I am not sure what those figures really mean...

     

    Regarding the latency errors, you may need to add additional ISLs between this switch and the 4100 but a deeper investigation should be performed on the fabric because usually latency event on a standard isl are caused by some kind of slow drain device in the fabric and not the isl itself.

     

     

    Rgds,

    Felipe

     

     

     

     


    #BrocadeFibreChannelNetworkingCommunity


  • 5.  Re: Brocade 5100 portbuffershow values "E" port

    Posted 10-30-2014 10:46 AM

    Thanks for the help Felipe,

     

     


    #BrocadeFibreChannelNetworkingCommunity


  • 6.  Re: Brocade 5100 portbuffershow values "E" port

    Posted 10-30-2014 10:48 AM

    Thanks for the help Felipe,

    I will add more buffers to the ISL's and continue my fabric analysis.

    During latencey erros, with trunkshow -perf - the bandwidth is very small < 10% max.

    I also have two ISL's to same switch.

     

    Now - I need to google how to find the slow drain device, unless again you come to the rescue :-)

     

     


    #BrocadeFibreChannelNetworkingCommunity